Heaters and Carbs!

I've had quite a busy weekend. I removed a whole stack of stuff from my car. The carbs came off first. I took them off complete with the manifold so that they can be posted off to Andrew Turner later on in the week. I spoke to him on the phone earlier on in the week and we had a good chat. He's going to take a look at them for me and get back to me to let me know what needs doing!

I also got going on fixing the heater. The controls for the temperature were completely seized so I started tracking down the problem. The heater lever assembly and the cable were okay (but a bit stiff and grubby) so the problem had to be the water valve. It was beyond repair so I ordered another. Then I started looking at the 'heat distribution' lever. This is supposed to direct the heat either to the footwell or onto the windscreen. This was seized solid as well but I couldn't see exactly what the problem was without getting the heater box out of the car.

Getting the heater box out wasn't as hard as I was expecting. All you need to do it to get the passenger glove box out, disconnect the heater, undo the bolts and then slip it out. I immediately noticed why the lever wasn't working. The linkage at the bottom of the heater had snapped off where the cable attaches. It could do with a new heater box as it's gone a bit rusty around where the pipes enter but at least the heater matrix looks to be in pretty decent condition. The heater motor is in tip top condition too which is a relief!

While I was mulling over what to do with the heater I removed the fuel pressure regulator. Hopefully this won't be needed when I get a new fuel pump that delivers the right pressure! I also spent some time ordering parts this week. A new heater valve showed up from Rimmer Bros on Thursday along with a thermostat, rear oil seal, gaskets and a kit that reduces gear lever 'rattle'. I also ordered an alloy water pump housing from Canley Classics that should be with me by the end of next week. I've decided not to go with an electric water pump on the grounds that I want to keep things simple so alloy will be the way forward for me!

Wheels!

I've finally got around to something I've been meaning to do for ages! After all this time I've finally joined Club Triumph! Now if I can only stay in the country long enough I can enter the RBRR or maybe even the 10CR!

I also finally got around to finishing off my slotmags. I was in a mad rush to get them done and on the car before I had to return to New Zealand. I had a morning to apply the last coats of paint, get them balanced and then finally fit them to the car! It seemed like mission impossible but I got it done just in time to take a few photos, pack my stuff and get on the plane! Of course there were a few hitches along the way. I couldn't get my hydraulic trolley jack under the front crossmember because the car's too low so I had to use a screw jack to raise it a couple of inches before I could slide the trolley jack under. I still need to polish the rims some more and I really need to get hold of some centre finishers to finish the job off but I think it looks pretty cool!

For some reason it now looks a bit higher off the ground than it did before. I rolled it backwards and forwards to let the suspension settle but it still seems to sit higher than before. I'll have to take it for a run and see how it looks after that before I decide what to do about it. I can just wind the AVO's down at the front but it looks like I may have to fit a lowering block at the rear. Thats another project for another time!

I've also recently joined Davesideways' new forum (http://www.sideways-technologies.co.uk/) and it looks to be shaping up quite nicely as good read for people who love their modified classics. I've already had a few more ideas that I will get around to another time. With me being on the other side of the world I don't think this is going to get updated too often over the next few months but I may have some news about parts I'm trying to aquire. Watch this space!

Finally! An Update!

Okay so its been a long time coming but here's the first update in quite some time! I've been busy over christmas but not on the car sadly...

I got back from NZ on the 28th of November and since then seeing the girlfriend, christmas and pilot exams have all taken their toll on my spare time but that dosent mean I havent been busy getting a few bits sorted out for the car!

I've always said that that time and money are the two biggest factors in how I work on my car. Sometimes I've got time and no money so I lighten up some stuff or do a few little jobs and sometimes I've got more money than time and I buy some nice shiny bits! I've not had the time recently so the shiny bits have been rolling in!

Here's a few bits and bobs I've recently aquired. First off is something I've been after for a while - an alloy engine backplate. I bought one of these from Dave 'Sideways' Powell a while back but postal incompetance meant that it never arrived so I bought one from Canley Classics the other week.

Wierdly it looks smaller when it's not on the car! Looks nicely made with all the holes in the right place so it gets the thumbs up from me! Not planning to fit it at the moment so I'll probably just chuck it in the parts box untill I can fit it. I'll probably leave it till I replace the clutch and chuck in a lightweight flywheel, race clutch, alloy bellhousing etc etc.

I also thought I'd treat myself to an alloy alternator bracket (again from Canley Classics). I know its not going to save a tonne of weight but it sure does look cool!

I've also had a chance to check out the rocker spacers. I might well take the rocker shaft out and rebuild it while I'm out in NZ to give me something to do on the boring days I'm not flying! I may even take the Dremel out there and smooth and polish the rockers up!

I've also been working on the wheels I bought. It's been an epic mission to strip all the old paint off. There were about four layers and each seemed to be better applied than the last. It took a whole bottle of nitromoors to get it sorted and even then it took an epic amount of time with wire wool and wire brushes to get the final bits of paint off! I'm still finishing them off but one is painted up nicely and the result is pretty good. What do you think?

Of course I had to get some nuts to bolt them up. I will eventually upgrade the studs, but for now I bought nuts to fit the standard size studs. I got them from Speedshack and I can thoroughly recommend them. They knew exactly what they were talking about and got them delivered in double quick time so they get a recommendation from me!

I'm also trying to fit the 'all orange' indicators that 'GT6Steve' sent me from Las Vegas but I've run into a bit of a stumbling block. It seems that the fitment of them to a UK spec spit is not as straightforward as it would seem. The bulb holding back part of the light is bigger than the UK ones so it needs the hole opening up with the trusty Dremel!

And finally a request for help! Anyone know how to remove the standard type of mirrors that come come on a Spitfire? I've only got one on the drivers side and theres a screw sunk into a recess on the back of it but it dosent seem to want to move! Do I have to get at it from the inside of the door?

Polished Alloy Valances

My grandad and I made these alloy radiator valances today. All we did was cut the aluminium (very easy when its only 2.5mm), sand down the edges, polish and give them a good coat of laquer. I then just drilled 3 holes in each so I could mount them to the radiator cradle with rivets.